How to Do a Decoder to Decoder Firmware Transfer Via Rs232 Cable


In two of my previous post, there has been a dire need to perform a decoder to decoder firmware transfer in other to either revive your dead fake strong decoder, or to revive your expired liberty decoder.

Must read: How to Upgrade Your Expired Liberty Star T1& T3 Decoder    

Or if your case is that of a dead fake / counterfeit strong decoder, then you can still wake it up by following the same tutorial.

how to connect a decoder to decoder for firmware transferMust read: Two Ways In Which You Can Revive Your Fried / Dead Fake Strong Decoder.

Like i said earlier, it may get to a point when a decoder to decoder firmware transfer will be inevitable. most especially in the two above mentioned case, where you can either not upgrade your fake strong decoder via rs232 or you cannot find a loader for your liberty decoder. Due to popular demand by (mostly novice) on how to transfer the firmware of on strong decoder to another strong decoder of the same model. E.g the two strong the coder must be the same model that . if it is strong 4669x then the two decoders must both be strong 4669x annd they must also be both fake decoders of which one is working and the other one dead. Please do not transfer firmwares between two different strong products.

As for liberty decoders, the same rules that applies to strong decoders above, also applies to it. so please don’t try to transfer the firmware of a working liberty decoder to an expired liberty decoder of different models. e.g don’t transfer t1 firmware to t3 decoder.

STEPS TO DO THE DECODER TO DECODER TRANSFER:

The steps is basically for strong, but you can apply it for liberty as well

1. You need to get a rs232 cable
2. Get another working decoder of that same type
3.connect the two decoder via rs232 and remember to switch off the fried / expired one
4. Switch on the good one. Go to – system setting – data transferfirmware – ok.

Wait till it finish loading. That’s all.

 

 

Comments

  1. hi boss, the cable RS 232 should be female female type before making the transfer between 2 decoder strong 4669xii?? thank

  2. i remove the lmb cable of my liberty decoder and later in the day i fix it back only for me to discover that that the decoder is returning no signal. what can i do to fix this.
    2) which is the best dstv adapter G1 AZSKY OR ECLICK X5

  3. MY BOSS NICE JOB U DOING PLS I HAVE ZSKY G1 CONNECTED TO MY LIBERTY T2 AND HAVE STRONG NETWORK SIGNAL VIEW WAS GOOD BUT RECENTLY IS NOT STABLE IS LIKE WATCHING SCRATCH DISC
    ON VIDEO DECK. SOMETIMES IT EFFECT MY MULTI TV DECODER TOO. UNLESS SOMETIMES I HOLD THE DB 9 CABLE AND IT WILL STOP SMALL, PLS WHAT DO YOU THINK IT WILL BE THE PROBLEM MY BOSS.
    SALUTE YOU MY BOSS

  4. BOSS AFTER THE UPGRADE HOW CAN U CHECK WEATHER UR LIBERTY DECODER WAS UPGRADED
    THANKS

  5. Gud Day. my freind. Plz can u tell me on fta is thr any place where we can watch sports like french open. previosly mbcsports 1 & 2 use to telecast tht bt nw no more.
    thankzz

  6. I had a strong srt 4330 decoder which was working normally until recently. When I switch it on, all I see on the decoder is ‘boot’ and it will stay forever and nothing displays on the TV screen. What could possibly be The problem? Could it be restored using the decoder to decoder transfer? Thanks in advance.

  7. Suleiman says:

    Hello sir,
    pls can i use card reader with memory card instead of flash drive to upgrade my reciever? Bcos i hv bought about 2-3 flash drives now and they were all affected by virus. Thanks in anticipation.

  8. Pls is the “Option” firmware for strong 4669xii decoder a downloadable file anywhere on the internet? I am in Ghana. I have the strong 4669xii decoder but does not have the “Option” firmware. How do I get it? Any help pls? Thanks.

  9. patrick says:

    my liberty has no data transfer in the settings. but has rs232 upgrade in the tools can l use that one to do the decoder to decoder transfer.

  10. paeffiong says:

    tnx for ur answer. bud to som dat my question easynt dat simple

  11. paefiong says:

    Nice updates.

    pls my question is on hw to diferentiate a fake decoder frm an original decoder

    tnx and remain blessed
    .

  12. paefiong says:

    Nice upates.

    u hav been mentioning abt fake strong
    decoders, pls my question is on hw to knw or differentiate a fake one frm an original one.

    tnx and alwys remain blessed

Leave a Reply to marcus Cancel reply

*